Kit Generator Stator + CDI Box + Flywheel for Arctic Cat TBX 500 | TRV 500 | 500 Manual | 500 Automatic 2003-2009

CAD$ 684.00
Availability: Out of stock
SKU
RMS900-106852

Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

106852-R00
Stator

Dimensions :
Interior diameter: 53 mm
Exterior diameter: 114 mm
Thickness: 13 mm
Length of wires stator to grommet: 110 mm
Length of wires grommet to plug: 100 mm
Length of pickup coil's wire to grommet: 380 mm

Other specifications :
Number of wires: 7
Number of plugs: 2
Number of pins: 7

CDI Box

Dimensions:
Height: 27 mm
Length: 106 mm
Width: 102 mm
Fixation holes center to center: 86 mm

Other specifications:
Number of plugs: 1
Number of pins: 16

Flywheel

Dimensions:
Exterior Diameter: 142mm
Interior Diameter: 116mm
Interior Diameter Center Housing: 19mm
Exterior Diameter Center Housing: 39mm
Thickness (exterior): 13mm
Thickness (interior): 9mm

Before installing your new stator
  • Check the AC output of the stator.
  • Replace any burned or corroded connectors on stator and regulator/rectifier
  • Check and repair any melted wiring.
  • Use hi-temp dielectric grease on all connectors

Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.

When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010".

Before installing your new CDI Box

Our CDI may use a different wire color code than your original.
All the wires are installed in the correct order; please do not change any of the wiring configurations.
This CDI is designed as a direct plug-in replacement and should be used as such.

Before installing your new Flywheel

Before attempting to start your Suzuki / Arctic Cat, adjusting the air gap is necessary. Rotate the flywheel so the raised node is lined up with the pick up/pulser coil and adjust as close as possible but no less than 0.010’’.

Brand New Kit Stator + PeakRPM CDI Box + Flywheel

  • All products shipped are tested
  • All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.
Brand new aftermarket stator

  • Direct replacement to your original unit
  • Plug-and-play, direct fit, easy installation.
  • Highest grade lamination materials
  • Highest grade copper windings, resistant to 200 degrees Celsius.
  • Pick up pulsar coil included
  • Connector included
  • Rubber grommet included

We have even included the opposite connector (main harness side) as we know these are often melted/corroded/defective and a major cause for repetitive electrical issues.

Brand new aftermarket PeakRPM CDI box
  • Our part is a Plug-and-play unit, direct fit, and easy to install.
  • Our PeakRPM CDI Box provides the optimal output for your ride
  • Higher grade of electronic components.
  • The Quality exceeds the OEM equipment
Brand New Magneto Flywheel Rotor
Write Your Own Review
You're reviewing:Kit Generator Stator + CDI Box + Flywheel for Arctic Cat TBX 500 | TRV 500 | 500 Manual | 500 Automatic 2003-2009
Your Rating
Customers Also Viewed
Currently there is no product to display.