High Output 250 Watt Generator Stator for Suzuki DR 650 SE 1996-2024 | OEM Repl.# 32101-32E00 / 32101-32E01
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
- 2024 Suzuki DR 650 SE
- 2023 Suzuki DR 650 SE
- 2022 Suzuki DR 650 SE
- 2021 Suzuki DR 650 SE
- 2020 Suzuki DR 650 SE
- 2019 Suzuki DR 650 SE
- 2018 Suzuki DR 650 SE
- 2017 Suzuki DR 650 SE
- 2016 Suzuki DR 650 SE
- 2015 Suzuki DR 650 SE
- 2014 Suzuki DR 650 SE
- 2013 Suzuki DR 650 SE
- 2012 Suzuki DR 650 SE
- 2011 Suzuki DR 650 SE
- 2010 Suzuki DR 650 SE
- 2009 Suzuki DR 650 SE
- 2008 Suzuki DR 650 SE
- 2007 Suzuki DR 650 SE
- 2006 Suzuki DR 650 SE
- 2005 Suzuki DR 650 SE
- 2004 Suzuki DR 650 SE
- 2003 Suzuki DR 650 SE
- 2002 Suzuki DR 650 SE
- 2001 Suzuki DR 650 SE
- 2000 Suzuki DR 650 SE
- 1999 Suzuki DR 650 SE
- 1998 Suzuki DR 650 SE
- 1997 Suzuki DR 650 SE
- 1996 Suzuki DR 650 SE
32101-32E01
Dimensions :
Interior diameter : 54 mm
Exterior diameter : 115 mm
Thickness : 18 mm
Length of wires stator to grommet : 140 mm
Length of wires grommet to plug : 825 mm
Length of pickup coil's wire to grommet : 80 mm
Other specifications :
Number of wires : 7
Number of plugs : 2
Number of pins : 7
Wire to wire resistance :
Alternator : White To White = 0.4 ohms +/-20%
Pickup : Green To Blue = 230 ohms +/-20%
Position Sensor : Black To white = 0.4 ohms +/-20%
Before installing your new stator
- Check the AC output of the stator.
- Replace any burned or corroded connectors on stator and regulator/rectifier
- Check and repair any melted wiring.
- Use hi-temp dielectric grease on all connectors
Before installing your new stator
- Check the AC output of the stator.
- Replace any burned or corroded connectors on stator and regulator/rectifier
- Check and repair any melted wiring.
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010’’.
Brand new aftermarket High output stator
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation.
- Highest grade lamination materials
- Highest grade copper windings, resistant to 200 degrees Celsius.
- Pick up pulsar coil included
- Connector included
- Rubber grommet included
- All products shipped are tested
20% MORE OUTPUT OVER STOCK, WORKS WITH ALL OTHER OEM COMPONENTS.
Our Part produces a maximum of 250 Watts at 5000 RPM
All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.