Stator for Yamaha 600 700 cc Carb L/C Mountain Max SX Venture V-Max 1997-2001 | OEM# 8CH-85510-02-00 / 8CH-85510-00-00
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
- 2001 Yamaha Venture 700
- 2001 Yamaha Venture 600
- 2001 Yamaha V-Max 600
- 2001 Yamaha SX 700 R
- 2001 Yamaha SX 600 R
- 2001 Yamaha Mountain Max 700
- 2001 Yamaha Mountain Max 600
- 2000 Yamaha Venture 700
- 2000 Yamaha Venture 600
- 2000 Yamaha V-Max 700 Deluxe
- 2000 Yamaha V-Max 700
- 2000 Yamaha V-Max 600
- 2000 Yamaha SX 700 R
- 2000 Yamaha SX 600 R
- 2000 Yamaha Mountain Max 700
- 2000 Yamaha Mountain Max 600
- 1999 Yamaha Venture 700
- 1999 Yamaha Venture 600
- 1999 Yamaha V-Max 700 SX
- 1999 Yamaha V-Max 700 ER
- 1999 Yamaha V-Max 700
- 1999 Yamaha V-Max 600 SX
- 1999 Yamaha V-Max 600 ER
- 1999 Yamaha Mountain Max 700
- 1998 Yamaha V-Max 700 SX
- 1998 Yamaha V-Max 700
- 1998 Yamaha Mountain Max 700
- 1997 Yamaha V-Max 700 SX
- 1997 Yamaha Mountain Max 700
- 1997 Yamaha Mountain Max 600
8CH-85510-00-00
8CH-85510-01-00
Dimensions :
Interior diameter : 42 mm
Exterior diameter : 103 mm
Thickness : 15 mm
Length of wires stator to grommet : 95 mm
Length of wires grommet to plug : 160 mm
Length of pickup coil's wire to grommet : 140 mm
Other specifications :
Number of wires : 6
Number of plugs : 2
Number of pins : 6
Wire to wire resistance :
Alternator : Yellow to White = 0.04 ohms +/- 20%
Pickup : Whte to White/Red = 225 ohms +/- 20%
Source 1 : Black to Brown/Red = 124 ohms +/- 20%
Source 2 : Brown to Black/Red = 443 ohms +/- 20%
- Check the AC output of the stator.
- Replace any burned or corroded connectors on stator and regulator/rectifier
- Check and repair any melted wiring.
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
For the pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010’’.
Brand new stator
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation.
- Highest grade lamination materials
- Highest grade copper windings, resistant to 200 degrees Celsius
- The quality exceeds the OEM equipment
- Pick up pulsar coil included
- Connector included
- Rubber grommet included
- All product shipped are tested
*All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.