Generator Stator for Arctic Cat 440 Sno Pro F5 Firecat 500 F6 / Sabercat 600 Sno Pro F7 Firecat 700 ZR 6000 2004-2016
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
- 2016 Arctic Cat ZR 6000 R SX
- 2015 Arctic Cat ZR 6000 R SX
- 2014 Arctic Cat ZR 6000 Sno Pro R Carb L/C
- 2013 Arctic Cat F6 600 Sno Pro Carb L/C
- 2012 Arctic Cat F6 600 Sno Pro Carb L/C
- 2011 Arctic Cat F6 600 Sno Pro Carb L/C
- 2010 Arctic Cat F6 600 Sno Pro Carb L/C
- 2009 Arctic Cat F6 600 Sno Pro Carb L/C
- 2008 Arctic Cat F6 600 Sno Pro Carb L/C
- 2007 Arctic Cat F6 600 Sno Pro Carb L/C
- 2006 Arctic Cat M7 700 Carb L/C
- 2006 Arctic Cat F7 Firecat 700 Sno Pro Carb L/C
- 2006 Arctic Cat F7 Firecat 700 Carb L/C
- 2006 Arctic Cat F5 Firecat 500 Carb L/C
- 2005 Arctic Cat F7 Firecat 700 Sno Pro Carb L/C
- 2005 Arctic Cat F7 Firecat 700 Carb L/C
- 2005 Arctic Cat F5 Firecat 500 Carb L/C
- 2005 Arctic Cat 440 Sno Pro Carb L/C
- 2004 Arctic Cat Sabercat 600 LX Carb L/C
- 2004 Arctic Cat Sabercat 600 Carb L/C
- 2004 Arctic Cat F7 Firecat 700 Sno Pro Carb L/C
- 2004 Arctic Cat F7 Firecat 700 Carb L/C
- 2004 Arctic Cat F6 Firecat 600 Carb L/C
- 2004 Arctic Cat F5 Firecat 500 Carb L/C
- 2004 Arctic Cat 440 Sno Pro Carb L/C
3006-705
Interior diameter : 38mm
Exterior diameter : 100mm
Thickness : 20mm
Length of wires stator to plug : 325mm
Other specifications :
Number of wires : 4
Number of plugs : 1
Number of pins : 4
Wire to wire resistance :
Alternator : Yellow/Red to Black = 0.4 ohms +/-20%
Source : Yellow to Brown = 1.0 ohms +/-20%
- Check the AC output of the stator.
- Replace any burned or corroded connectors on stator and regulator/rectifier
- Check and repair any melted wiring.
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original. `
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010’’.
Brand new generator stator
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation.
- Highest grade lamination materials
- Highest grade copper windings, resistant to 200 degrees Celsius.
- Connector included
- All products shipped are tested
All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.