Generator Stator for Yamaha YFZ 450 X / YFZ 450 R 2009-2024 OEM# 18P-81410-00-00
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
- 2024 Yamaha YFZ 450 R
- 2023 Yamaha YFZ 450 R SE
- 2023 Yamaha YFZ 450 R
- 2022 Yamaha YFZ 450 R SE
- 2022 Yamaha YFZ 450 R
- 2021 Yamaha YFZ 450 R SE
- 2021 Yamaha YFZ 450 R
- 2020 Yamaha YFZ 450 R SE
- 2020 Yamaha YFZ 450 R
- 2019 Yamaha YFZ 450 R SE
- 2019 Yamaha YFZ 450 R
- 2018 Yamaha YFZ 450 R SE
- 2018 Yamaha YFZ 450 R
- 2017 Yamaha YFZ 450 R SE
- 2017 Yamaha YFZ 450 R
- 2016 Yamaha YFZ 450 R SE
- 2016 Yamaha YFZ 450 R
- 2015 Yamaha YFZ 450 R SE
- 2015 Yamaha YFZ 450 R
- 2014 Yamaha YFZ 450 R SE
- 2014 Yamaha YFZ 450 R
- 2013 Yamaha YFZ 450 R SE
- 2013 Yamaha YFZ 450 R
- 2012 Yamaha YFZ 450 R SE
- 2012 Yamaha YFZ 450 R
- 2011 Yamaha YFZ 450 X SE
- 2011 Yamaha YFZ 450 X
- 2011 Yamaha YFZ 450 R SE
- 2011 Yamaha YFZ 450 R
- 2010 Yamaha YFZ 450 X Bill Balance
- 2010 Yamaha YFZ 450 X
- 2010 Yamaha YFZ 450 R SE
- 2010 Yamaha YFZ 450 R
- 2009 Yamaha YFZ 450 R SE
- 2009 Yamaha YFZ 450 R
Dimensions :
Interior diameter : 37 mm
Exterior diameter : 97 mm
Thickness : 14 mm
Length of wires stator to grommet : 130 mm
Length of wires grommet to plug : 110 mm
Length of pickup coil's wire to grommet : 220 mm
Other specifications :
Number of wires : 5
Number of plugs : 2
Number of pins : 5
Wire to wire resistance :
Alternator : White to White = 0.4 ohms +-20%
Pickup : Black to White = 250 ohms +-20%
Before installing your new stator
- Check the AC output of the stator.
- Replace any burned or corroded connectors on stator and regulator/rectifier
- Check and repair any melted wiring.
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010’’.
Brand new aftermarket stator
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation.
- Highest grade lamination materials
- Highest grade copper windings, resistant to 200 degrees Celsius.
- Pick up pulsar coil included
- Connector included
- All products shipped are tested
All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.