Generator Stator for Kawasaki Vulcan 1500 1600 Drifter / Nomad / Classic / Mean Streak 1999-2008 | 21003-1326 21003-1375
Please note there is a possibility of two stators with certain models
This stator can replaces the inner stator and the outer stator
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
- 2008 Kawasaki VN 1600 Vulcan Mean Streak
- 2008 Kawasaki VN 1600 Vulcan
- 2008 Kawasaki VN 1500 Vulcan Classic
- 2007 Kawasaki VN 1600 Vulcan Mean Streak
- 2007 Kawasaki VN 1600 Vulcan
- 2007 Kawasaki VN 1500 Vulcan Classic
- 2006 Kawasaki VN 1600 Vulcan Mean Streak
- 2006 Kawasaki VN 1600 Vulcan
- 2006 Kawasaki VN 1500 Vulcan Classic
- 2005 Kawasaki VN 1600 Vulcan Mean Streak
- 2005 Kawasaki VN 1600 Vulcan
- 2005 Kawasaki VN 1500 Vulcan Drifter
- 2005 Kawasaki VN 1500 Vulcan Classic
- 2004 Kawasaki VN 1600 Vulcan Mean Streak
- 2004 Kawasaki VN 1600 Vulcan
- 2004 Kawasaki VN 1500 Vulcan Nomad
- 2004 Kawasaki VN 1500 Vulcan Drifter
- 2004 Kawasaki VN 1500 Vulcan Classic
- 2003 Kawasaki VN 1600 Vulcan
- 2003 Kawasaki VN 1500 Vulcan Nomad
- 2003 Kawasaki VN 1500 Vulcan Mean Streak
- 2003 Kawasaki VN 1500 Vulcan Drifter
- 2003 Kawasaki VN 1500 Vulcan Classic
- 2002 Kawasaki VN 1500 Vulcan Nomad
- 2002 Kawasaki VN 1500 Vulcan Mean Streak
- 2002 Kawasaki VN 1500 Vulcan Drifter
- 2002 Kawasaki VN 1500 Vulcan Classic
- 2001 Kawasaki VN 1500 Vulcan Nomad
- 2001 Kawasaki VN 1500 Vulcan Drifter
- 2001 Kawasaki VN 1500 Vulcan Classic
- 2000 Kawasaki VN 1500 Vulcan Nomad
- 2000 Kawasaki VN 1500 Vulcan Classic
- 1999 Kawasaki VN 1500 Vulcan Nomad
- 1999 Kawasaki VN 1500 Vulcan Classic
21003-1372
21003-1375
21003-1326
21003-1376
21003-1373
21003-0008
21003-1356
21003-0007
Dimensions :
Interior diameter : 58 mm
Exterior diameter : 130 mm
Thickness : 21 mm
Length of wires stator to grommet : 70 mm
Length of wires grommet to plug : 125 mm
Other specifications :
Number of wires : 3
Number of plugs : 1
Number of pins : 3
Wire to wire resistance :
Alternator : Black to Black = 0.7 ohms +-20%
Before installing your new stator
- Check the AC output of the stator
- Replace any burned or corroded connectors on stator and regulatorrectifier
- Check and repair any melted wiring
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010'.
Brand new aftermarket generator stator
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation
- Highest grade lamination materials
- Highest grade copper windings, resistant to 200 degrees Celsius.
- Connector included
- Rubber grommet included
- All products shipped are tested
We have even included the opposite connector (main harness side) as we know these are often melted / corroded / defective and a major cause for repetitive electrical issues.
All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.