Aluminum Mosfet bypass Voltage Regulator rect. for Kawasaki KLF 300 Bayou | KVF 360 400 650 1999-2013 OEM# 21066-0047
NEW WIRE HARNESS BYPASS DESIGN
The failure-prone harnesses on Kawasaki are known to develop corrosion which increases electrical resistance, which in turn, increases the temperature of wires to the point where connectors start melting. When this happen, the voltage regulator (and most likely the stator) is failing incurring steep repair expenses.
Our new bypass voltage regulator brings back the renowned RMSTATOR Mosfet technology with the RMSTATOR machined aluminum case in a new configuration designed to bypass the main wiring harness and connect the voltage regulator directly to the battery. This configuration has demonstrated a major increase in voltage regulator reliability in real life scenarios over the years.
Features
Mosfet circuit
Significantly lowers the operating temperature for an increased voltage regulator lifespan. Provide a steadier and smoother signal to the battery.
Billet aluminum housing
Runs 33% cooler than standard cast voltage regulator housings.
PRO-FIT System
Includes everything required to perform a RMSTATOR-style professional installation: part connectors, harness-side connectors & dielectric connector grease.
2-Year Warranty
Covered with a 2-year warranty for a complete peace of mind
- RMS022-106222
- RMS022-107616
- 2013 Kawasaki KVF 650 Brute Force
- 2013 Kawasaki KVF 360 Prairie
- 2012 Kawasaki KVF 650 Brute Force
- 2012 Kawasaki KVF 360 Prairie
- 2011 Kawasaki KVF 650 Brute Force
- 2011 Kawasaki KVF 360 Prairie
- 2010 Kawasaki KVF 650 Brute Force
- 2010 Kawasaki KVF 360 Prairie
- 2009 Kawasaki KVF 650 Brute Force
- 2009 Kawasaki KVF 360 Prairie
- 2009 Kawasaki KFX 700
- 2008 Kawasaki KVF 650 Brute Force
- 2008 Kawasaki KVF 360 Prairie
- 2008 Kawasaki KFX 700
- 2007 Kawasaki KVF 650 Brute Force
- 2007 Kawasaki KVF 360 Prairie
- 2007 Kawasaki KFX 700
- 2006 Kawasaki KVF 700 Prairie
- 2006 Kawasaki KVF 650 Brute Force
- 2006 Kawasaki KVF 360 Prairie
- 2006 Kawasaki KFX 700
- 2005 Kawasaki KVF 700 Prairie
- 2005 Kawasaki KVF 650 Brute Force
- 2005 Kawasaki KVF 360 Prairie
- 2005 Kawasaki KLF 300 Bayou C Euro
- 2005 Kawasaki KFX 700
- 2004 Kawasaki KVF 700 Prairie
- 2004 Kawasaki KVF 360 Prairie
- 2004 Kawasaki KLF 300 Bayou C
- 2004 Kawasaki KLF 300 Bayou B
- 2004 Kawasaki KFX 700
- 2003 Kawasaki KVF 650 Prairie
- 2003 Kawasaki KVF 360 Prairie
- 2003 Kawasaki KLF 300 Bayou C
- 2003 Kawasaki KLF 300 Bayou B
- 2002 Kawasaki KVF 650 Prairie
- 2002 Kawasaki KVF 400 Prairie
- 2002 Kawasaki KVF 300 Prairie
- 2002 Kawasaki KLF 300 Bayou C
- 2002 Kawasaki KLF 300 Bayou B
- 2001 Kawasaki KVF 400 Prairie
- 2001 Kawasaki KVF 300 Prairie
- 2001 Kawasaki KLF 300 Bayou C
- 2001 Kawasaki KLF 300 Bayou B
- 2000 Kawasaki KVF 400 Prairie
- 2000 Kawasaki KVF 300 Prairie
- 2000 Kawasaki KLF 300 Bayou C
- 2000 Kawasaki KLF 300 Bayou B
- 1999 Kawasaki KVF 400 Prairie
- 1999 Kawasaki KVF 300 Prairie
- 1999 Kawasaki KLF 300 Bayou C
- 1999 Kawasaki KLF 300 Bayou B
21066-1112
Dimensions:
Width: 95 mm
Length: 90 mm
Height: 30 mm
Wires length: 811 mm & 350 mm
Fixation holes center to center: 75 mm
Other specifications:
Number of plugs: 2
Number of pins: 5
Number of wires: 5
Minimum Charging Voltage: 14.5 V +/- 0.5 V
Maximum Charging Current: 50 A / 500 W
Open Circuit Voltage: < 15 V
Operation Temperature: -20° to 85°
Before installing your new Machined Aluminum Mosfet voltage regulator rectifier:
- Check the AC output of the stator
- Replace any burned or corroded connectors on stator and regulator rectifier
- Check and repair any melted wiring
- Use hi-temp dielectric grease on all connectors
Brand new RMSTATOR Red Machined Aluminum Mosfet Regulator
Our new RMSTATOR machined aluminum Mosfet voltage regulator is a great upgrade for heat dissipation in any powersports charging system. After 10 minutes of use, our billet aluminum heatsink runs cooler by 33% than standard cast regulator housings. Our new RMSTATOR red regulator, equipped with the renowned Mosfet regulation technology, is an added value to any three-phase permanent magnet charging system.
STOP BURNING YOUR REGULATOR RECTIFIER !It is time to update or replace your voltage regulator with the advanced MOSFET type.
It runs cooler than all OEM diode style regulators. In addition, this rectifier has overheat protection, rather than burn up, it will simply turn off for a while and cool off.
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation.
- The quality exceeds the OEM equipment
- Improved heat sink and charging capabilities
- Higher grade of electric components
- All shipped products are tested
We have even included the opposite connector (main harness side) as we know these are often melted / corroded / defective and a major cause of repetitive electrical issues.
*All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part.
Why use Mosfet Enhanced technology?
Runs cooler
Runs much cooler than the traditional Shunt voltage regulator rectifier.
Saves gas
Less load on the stator, less work, less fuel is used and you save.
Regulated energy
The power charging your battery is steadier and smooth.
Extended battery life
Extends the battery’s life and cold cranking capacity.
More engine power
Removes stator load resulting in more engine power.
Optimized power
Optimize power delivery by switching the stator coils on or off.