Flywheel Puller M33 X 1.5 R.H. for Yamaha WR 250 F / WR 250 R / WR 250 X / WR 426 / XS 650 / S 1975-2020

• 2020 Yamaha WR 250 R
• 2019 Yamaha WR 250 R
• 2018 Yamaha WR 250 R
• 2017 Yamaha WR 250 R
• 2016 Yamaha WR 250 R
• 2015 Yamaha WR 250 R
• 2014 Yamaha WR 250 R
• 2013 Yamaha WR 250 R
• 2013 Yamaha WR 250 F
• 2012 Yamaha WR 250 R
• 2012 Yamaha WR 250 F
• 2011 Yamaha WR 250 X
• 2011 Yamaha WR 250 R
• 2011 Yamaha WR 250 F
• 2010 Yamaha WR 250 X
• 2010 Yamaha WR 250 R
• 2009 Yamaha WR 250 X
• 2009 Yamaha WR 250 R
• 2009 Yamaha WR 250 F
• 2008 Yamaha WR 250 X
• 2008 Yamaha WR 250 R
• 2008 Yamaha WR 250 F
• 2007 Yamaha WR 250 F
• 2006 Yamaha WR 250 F
• 2005 Yamaha WR 250 F
• 2004 Yamaha WR 250 F
• 2003 Yamaha WR 450 F
• 2003 Yamaha WR 250 F
• 2002 Yamaha WR 426
• 2002 Yamaha WR 250 F
• 2001 Yamaha WR 426
• 2001 Yamaha WR 250 F
• 1983 Yamaha XS 650 S
• 1982 Yamaha XS 650 S
• 1981 Yamaha XS 650 S
• 1981 Yamaha XS 650
• 1980 Yamaha XS 650 S
• 1980 Yamaha XS 650
• 1979 Yamaha XS 650 S
• 1979 Yamaha XS 650
• 1978 Yamaha XS 650 S
• 1978 Yamaha XS 650
• 1977 Yamaha XS 650
• 1976 Yamaha XS 650
• 1975 Yamaha XS 650
• 1974 Yamaha TX 650
• 1973 Yamaha TX 650
• 1972 Yamaha XS2
• 1971 Yamaha XS1
• 1970 Yamaha XS1

Specifications:
Length: 45.2 mm
Exterior Diameter: 30.17 mm
Interior Diameter: 23.14 mm
Exterior Diameter Center Housing: 15.19 mm

Removing a Powersport Vehicle's Flywheel / Rotor:

How it Works

Flywheel Pullers are very versatile engine service tools and are a must in every toolbox. Our large selection of best selling rotor and flywheel pullers fit just about any motorcycle or ATV. Flywheel pullers are very simple to use, having only an outer body to hold the flywheel and a screw to push on the crankshaft. Some are even simpler, having only a bolt to thread into the flywheel. A taper holds the flywheel or rotor and the crankshaft together. The flywheel is secured to the shaft by applying torque to the fixing bolt.

An Important Component to use

Many flywheel or rotor puller tools will include a small cap. This is a crankshaft thread protector, and should always be used if it is included with the puller. You slip this cap onto the end of the inner piece of the puller which presses against the tip of the crankshaft. This keeps the fine threads from being stripped or damaged while removing the flywheel or rotor.

Actions to Avoid

Most of the time, removing a flywheel or rotor is painless. But sometimes corrosion, over-torquing the fixing bolt, or heat-cycling can give you a hard time removing the flywheel. We too often see mechanics use a larger breaker bar or air impact tools to ease the flywheel off. These two techniques will damage the flywheel, the flywheel puller, or the crank. Avoid using them if you want to keep it cheap.

Tips to break a stuck flywheel loose:

Torque Wrench

How do you know if it's stuck? You simply have to set your torque wrench to 50 ft-lbs and try to ease the flywheel off. If the flywheel is not stuck, you should be able to remove it with even less torque than this. If it is stuck, don't use more torque or you might break your wrench.

Ball Peen Hammer

If 50 ft-lbs does not do the trick, go fetch something like a 12 or 16 oz ball peen hammer. Hit the end of the flywheel puller with a medium blow. Many times, the shock you create will successfully remove your flywheel. Be prepared to catch the flywheel since the shock of the hammer can make the flywheel jump off. Once again, getting into that situation will be pricey. And don't forget your safety glasses.

Propane Torch

The hammer is not a be-all, end-all solution. Sometimes, you will have to find something more powerful, and that's where the propane torch comes in. As a last resort solution, the heat should expand the flywheel but not the crank, since it is too massive to expand as fast. That way, the flywheel will become looser and will come off easier.
Important Security Tips: In order to not set fire to your garage, your vehicle, or yourself, certain precautions are necessary prior to heating the flywheel:

• Clean any oil or flammable liquids off the flywheel;
• Make sure your work area is free of any flammable liquids and that you work in a well ventilated area;
• Make sure to remove the gas tank, and set it aside at a safe distance.

Make sure the flame of your torch is focused, and heat only the center of the flywheel. This is due to the fact that some flywheels use adhesive or other fixing compounds to locate the magnets in the rim that can be damaged by concentrated heat. Here again, the wheel might fall off the crank, so be prepared to catch it. And remember that you just heated it, so make sure you can catch it without burning yourself.

With these tips and techniques, you are now equipped to handle any stuck flywheel without throwing your flywheel puller at it; unless you have a habit of working with machines that have been in a lake for months!