Kit Flywheel Rotor + Flywheel Puller MP37 for Ski-Doo MX Z / MX ZX / Summit 440 500 600 700 800 cc 2003-2007

• 2007 Ski-doo MX ZX 440 Racing Carb L/C
• 2004 Ski-doo Summit 800 HO Carb L/C
• 2004 Ski-doo MX ZX 600 HO Carb L/C
• 2004 Ski-doo MX Z 600 HO Trail Carb L/C
• 2004 Ski-doo MX Z 600 HO Adrenaline Carb L/C
• 2004 Ski-doo MX Z 500 SS Trail Carb L/C
• 2003 Ski-doo Summit 800 HO X Carb L/C
• 2003 Ski-doo Summit 800 HO Highmark X Carb L/C
• 2003 Ski-doo Summit 800 HO Highmark Carb L/C
• 2003 Ski-doo Summit 800 HO Adrenaline Carb L/C
• 2003 Ski-doo Summit 700 X Carb L/C
• 2003 Ski-doo Summit 700 Highmark Carb L/C
• 2003 Ski-doo Summit 700 Carb L/C
• 2003 Ski-doo Summit 700 Adrenaline Carb L/C
• 2003 Ski-doo Summit 600 HO Adrenaline Carb L/C
• 2003 Ski-doo MX ZX 800 Carb L/C
• 2003 Ski-doo MX ZX 600 HO Carb L/C
• 2003 Ski-doo MX Z 800 Sport Carb L/C
• 2003 Ski-doo MX Z 800 Renegade Carb L/C
• 2003 Ski-doo MX Z 800 Adrenaline Carb L/C
• 2003 Ski-doo MX Z 700 Adrenaline Carb L/C
• 2003 Ski-doo MX Z 600 Trail Carb L/C
• 2003 Ski-doo MX Z 600 HO Trail Carb L/C
• 2003 Ski-doo MX Z 600 HO Sport Carb L/C
• 2003 Ski-doo MX Z 600 HO Renegade Carb L/C
• 2003 Ski-doo MX Z 600 HO Adrenaline Carb L/C
• 2003 Ski-doo MX Z 600 Carb L/C
• 2003 Ski-doo MX Z 500 Trail Carb L/C
• 2003 Ski-doo MX Z 500 Adrenaline Carb L/C

Dimensions:
Exterior Diameter: 128 mm
Interior Diameter: 104 mm
Interior Diameter Center Housing: 27 mm
Exterior Diameter Center Housing: 24 mm
Thickness (exterior): 53 mm
Thickness (interior): 38 mm
Long Lump (timing trigger ridge): 25 mm

12 Holes Disc, 6 mm & 8 mm Bolts

Before attempting to start your Ski Doo, adjusting the air gap is necessary. Rotate the flywheel so the raised node is lined up with the pick up/pulsar coil and adjust as close as possible but no less than 0.010’’.

Removing a Powersport Vehicle's Flywheel / Rotor:

How it Works

Flywheel Pullers are very versatile engine service tools and are a must in every toolbox. Our large selection of best selling rotor and flywheel pullers fit just about any motorcycle or ATV. Flywheel pullers are very simple to use, having only an outer body to hold the flywheel and a screw to push on the crankshaft. Some are even simpler, having only a bolt to thread into the flywheel. A taper holds the flywheel or rotor and the crankshaft together. The flywheel is secured to the shaft by applying torque to the fixing bolt.

An Important Component to use

Many flywheel or rotor puller tools will include a small cap. This is a crankshaft thread protector, and should always be used if it is included with the puller. You slip this cap onto the end of the inner piece of the puller which presses against the tip of the crankshaft. This keeps the fine threads from being stripped or damaged while removing the flywheel or rotor.

Actions to Avoid

Most of the time, removing a flywheel or rotor is painless. But sometimes corrosion, over-torquing the fixing bolt, or heat-cycling can give you a hard time removing the flywheel. We too often see mechanics use a larger breaker bar or air impact tools to ease the flywheel off. These two techniques will damage the flywheel, the flywheel puller, or the crank. Avoid using them if you want to keep it cheap.

Tips to break a stuck flywheel loose:

Torque Wrench

How do you know if it's stuck? You simply have to set your torque wrench to 50 ft-lbs and try to ease the flywheel off. If the flywheel is not stuck, you should be able to remove it with even less torque than this. If it is stuck, don't use more torque or you might break your wrench.

Ball Peen Hammer

If 50 ft-lbs does not do the trick, go fetch something like a 12 or 16 oz ball peen hammer. Hit the end of the flywheel puller with a medium blow. Many times, the shock you create will successfully remove your flywheel. Be prepared to catch the flywheel since the shock of the hammer can make the flywheel jump off. Once again, getting into that situation will be pricey. And don't forget your safety glasses.

Propane Torch

The hammer is not a be-all, end-all solution. Sometimes, you will have to find something more powerful, and that's where the propane torch comes in. As a last resort solution, the heat should expand the flywheel but not the crank, since it is too massive to expand as fast. That way, the flywheel will become looser and will come off easier.
Important Security Tips: In order to not set fire to your garage, your vehicle, or yourself, certain precautions are necessary prior to heating the flywheel:

• Clean any oil or flammable liquids off the flywheel;
• Make sure your work area is free of any flammable liquids and that you work in a well ventilated area;
• Make sure to remove the gas tank, and set it aside at a safe distance.

Make sure the flame of your torch is focused, and heat only the center of the flywheel. This is due to the fact that some flywheels use adhesive or other fixing compounds to locate the magnets in the rim that can be damaged by concentrated heat. Here again, the wheel might fall off the crank, so be prepared to catch it. And remember that you just heated it, so make sure you can catch it without burning yourself.

With these tips and techniques, you are now equipped to handle any stuck flywheel without throwing your flywheel puller at it; unless you have a habit of working with machines that have been in a lake for months!