Stator for KTM 950 990 Adventure S SuperMoto Super Duke Super Enduro 2003-2013
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
- 2013 KTM 990 Supermoto T
- 2013 KTM 990 Adventure
- 2012 KTM 990 Supermoto T
- 2012 KTM 990 Adventure
- 2011 KTM 990 Supermoto T
- 2011 KTM 990 Supermoto R
- 2011 KTM 990 Adventure
- 2010 KTM 990 Supermoto T
- 2010 KTM 990 Supermoto R
- 2010 KTM 990 Adventure
- 2009 KTM 990 Adventure
- 2009 KTM 950 Super Enduro
- 2008 KTM 990 SuperDuke
- 2008 KTM 990 Adventure S
- 2008 KTM 990 Adventure
- 2008 KTM 950 SuperMoto
- 2008 KTM 950 Super Enduro
- 2007 KTM 990 SuperDuke
- 2007 KTM 990 Adventure S
- 2007 KTM 990 Adventure
- 2007 KTM 950 SuperMoto
- 2007 KTM 950 Super Enduro
- 2006 KTM 990 SuperDuke
- 2006 KTM 990 Adventure S
- 2006 KTM 990 Adventure
- 2006 KTM 950 SuperMoto
- 2006 KTM 950 Adventure S
- 2006 KTM 950 Adventure
- 2005 KTM 990 SuperDuke
- 2005 KTM 950 SuperMoto
- 2005 KTM 950 Adventure S
- 2005 KTM 950 Adventure
- 2004 KTM 950 Adventure S
- 2004 KTM 950 Adventure
- 2003 KTM 950 Adventure S
- 2003 KTM 950 Adventure
Dimensions :
Interior diameter : 42 mm
Exterior diameter : 104 mm
Thickness : 22 mm
Length of wires stator to grommet : 100 mm
Length of wires grommet to plug : 250 mm
Other specifications :
Number of wires : 3
Number of plugs : 1
Number of pins : 3
Wire to wire resistance :
Alternator : White between white = 0.4 ohms +-20%
Before installing your new stator
- Check the AC output of the stator
- Replace any burned or corroded connectors on stator and regulatorrectifier
- Check and repair any melted wiring
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010".
Brand new aftermarket stator
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation
- Highest grade lamination materials
- Highest grade copper windings, resistant to 200 degrees Celsius.
- Connector included
- Rubber grommet included
- All products shipped are tested
We have even included the opposite connector (main harness side) as we know these are often melted / corroded / defective and a major cause for repetitive electrical issues.
All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.