Stator + Regulator + CDI + Coil + Flywheel + Puller for Yamaha Banshee 1997-2006

CAD$ 671.00
Availability: In stock
SKU
RM22844
RM22844
Stator
Interior diameter : 103mm
Exterior diameter : 34mm
Thickness : 27mm
Length of wires stator to grommet : 60mm
Length of wires grommet to plug : 520mm
Length of pickup coil's wire to grommet : 80mm

Other specifications :
Number of wires : 6
Number of plugs : 3
Number of pins : 6

Wire to wire resistance :
Alternator : Yellow to Black = 0.4ohms +/-20%
Pickup : White/Green to White/Red = 115ohms +/-20%
Source : Green to Red = 12ohms +/-20%

Dimensions AC Regulator:
Height: 20 mm
Length: 45 mm
Width: 45 mm

Other specifications:
Number of terminals: 2
Wires length: 130 mm

Dimensions High Performance CDI Box:
Height: 25mm
Length: 87mm
Width: 71mm
Fixation holes center to center: 85mm

Other specifications:
Number of plugs: 2
Number of pins: 8

External Ignition coil
Distance between fixation holes: 90mm
Before installing your new stator
  • Check the AC output of the stator.
  • Replace any burned or corroded connectors on stator and regulator/rectifier
  • Check and repair any melted wiring.
  • Use hi-temp dielectric grease on all connectors

Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.

When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010".

CDI Box HP

Our CDI may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This CDI is designed as a direct plug-in replacement and should be used as such.

Flywheel

Before attempting to start your banshee adjusting the air gap is necessary.

Rotate the flywheel so the raised node is lined up with the pick up/pulsar coil and adjust as close as possible but no less than 0.010メメ.


External ignition coil

Remove the yellow wire from the external ignition coil, if it is not applicable to your model.


Brand New Kit Stator + High Performance CDI Box + External Ignition Coil + Flywheel + Puller

  • Direct replacement to your original unit
  • Plug-and-play, direct fit, easy installation
  • All shipped products are tested

*All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part.

High Output Stator
  • Highest grade of lamination materials
  • Highest grade of copper winding, resistant to 200 degrees Celsius
  • Pick up pulsar coil included
  • Connector included
  • Rubber grommet included
  • Back Plate included

For a limited time we are including a FREE Tympanum AC regulator required to run the extra wattage supplied from our 200W stator.

  • AC Regulator
  • 12 Volts regulator used by Baja winners
  • For use with all standard halogen and quartz lights
  • Precise voltage control, eliminates light burnout
  • Reduce flickering and dimming
  • Simple installation
  • Works with all other OEM parts
  • Rated at 225 watts
High Performance CDI Box:
  • Enhanced timing curve, increased rev limiter (approximately 1000 rpm)
  • Higher grade of electronic components
External Ignition Coil
  • Highest grade of lamination materials
  • Spark plug cap(s) included
Improved Stronger Magneto Flywheel Rotor
RMSTATOR is offering a new replacement flywheel with stronger magnetsfor your Banshee. This flywheel can be used as a direct replacement to the OEM.
We suggest combining it to our 100 or 200 watt stator as it will run the lights better in the lower rpm's.
Write Your Own Review
You're reviewing:Stator + Regulator + CDI + Coil + Flywheel + Puller for Yamaha Banshee 1997-2006
Your Rating
Customers Also Viewed
Currently there is no product to display.