- Store vehicles in your garage
- Get product recommendations
- Easily find products and accessories
Kit Lighting Stator + Regulator for Honda XR 80 / 100 R | CRF 80 / 100 F 1992-2013 | OEM # 31120-GN1-691 / 31120-KN4-751
RMSTATOR
SKU: RMS900-106771
In Stock
RMSTATOR
Kit Lighting Stator + Regulator for Honda XR 80 / 100 R | CRF 80 / 100 F 1992-2013 | OEM # 31120-GN1-691 / 31120-KN4-751
Close
FITMENT WARNING:
Close
Close
Shop By Vehicle
Please note: The OEM stator did not include a lighting coil because no lights come on the bike. If you would like to add a headlight and/or taillight, our stator includes a 100 Watt lighting coil between the Yellow wire and ground. The Black wire from the regulator needs to be grounded to the frame, and the Yellow wire is connected to the Yellow wire from the stator and also to your lights (the other side of your lights are grounded to the frame to complete the circuit). A new regulator must be used to support the lighting.
Please note: the body is different than the OEM (fix it with only one screw instead of two), but it works on the same models.
Please note: this regulator has two wires, yellow to power and black to ground.
This part can fits Mitsuba configuration
Battery condition is important. No stator or regulator can make up for a bad or weak battery. If in doubt, charge your battery and have it load tested, or simply replace it. ALWAYS START WITH A FULLY CHARGED BATTERY !
Read more
Kit Lighting Stator + Regulator for Honda XR 80 / 100 R | CRF 80 / 100 F 1992-2013 | OEM # 31120-GN1-691 / 31120-KN4-751
Details
Details
Brand new Kit Lighting Stator + AC Voltage Regulator Rectifier
- All item pictures are accurate; if in doubt, do not hesitate to compare our item to your original part
- All products shipped are tested
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation
- Highest grade of lamination materials
- Highest grade of copper winding, resistant to 200 degrees Celsius
- Pick up pulsar coil included
- Rubber grommet included
- 12 Volts regulator used by Baja winners
- Heavy duty and improved regulator rectifier
- For use with all standard halogen and quartz lights
- Precise voltage control, eliminates light burnout
- Reduce flickering and dimming
- Simple installation
- Works with all other OEM part
- Rated at 225 watts
Specifications
Specifications
Stator Dimensions:
Interior diameter : 30 mm
Exterior diameter : 85 mm
Thickness : 32 mm
Length of wires stator to grommet : 185 mm
Length of wires grommet to terminals : 355 mm
Length of pickup coil's wire to grommet : 78 mm
Other specifications :
Number of wires : 3
Number of pins : 3
Wire to wire resistance :
Alternator : Yellow to Ground = 0.4 ohms +-20%
Pickup : Blue/Yellow to Ground = 120 ohms +-20%
Source : Black/Red to Ground = 500 ohms +-20%
Voltage Regulator Rectifier Dimensions:
Width : 45 mm
Length : 45 mm
Height: 20 mm
Other specifications :
Number of pins : 2
Minimum Charging Voltage: 13 V +/- 0.5 V
Maximum Charging Current: 6 A - 10 A / 50 W - 200 W
Open Circuit Voltage: <15 V
Operation Temperature: -20? to 85?
Please note : this regulator has two wires, yellow to power and black to ground.
Interchange Part Nº
Interchange Part Nº
- 31120-KN4-751
- 31120-GN1-691
Installation
Installation
Before installing your new Stator:
- Check the AC output of the stator
- Replace any burned or corroded connectors on stator and regulator rectifier
- Check and repair any melted wiring
- Use hi-temp dielectric grease on all connectors
Before installing your new Voltage Regulator Rectifier:
- Check the AC output of the stator
- Replace any burned or corroded connectors on stator and regulator rectifier
- Check and repair any melted wiring
- Use hi-temp dielectric grease on all connectors
Our stator might have a different wire color code than your original part.
All the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible but no less than 0.010".
To add headlights to your vehicle:
- The stator includes a 100 watts lighting coil between the yellow wire and the ground
- Ground the black wire from the regulator to the frame
- Connect both yellow wires from the regulator and the lights to the yellow wire from the stator
- Ground the other side of your lights to the frame to complete the circuit
Warning:
Risk of electric shock. Disconnect the battery before servicing.
Ensure proper installation by a qualified technician to avoid malfunction.
Vehicle Fitments
Vehicle Fitments
Vehicle Fitments
Recently Viewed
You may also like
Have a question?
Our customers are our most important asset, we are here to help you in real time! Call us now, or connect with a specialist via email.
