Kit Stator + Gasket + Mosfet Regulator for Yamaha YFM 550 / 700 Grizzly 2007-2015 | # 3B4-81410-00-00 / 1D7-81960-00-00
- 2016 Yamaha YFM 700 Grizzly
- 2015 Yamaha YFM 700 Grizzly
- 2014 Yamaha YFM 700 Grizzly
- 2014 Yamaha YFM 550 Grizzly
- 2013 Yamaha YFM 700 Grizzly
- 2013 Yamaha YFM 550 Grizzly
- 2012 Yamaha YFM 700 Grizzly
- 2012 Yamaha YFM 550 Grizzly
- 2011 Yamaha YFM 700 Grizzly
- 2011 Yamaha YFM 550 Grizzly
- 2010 Yamaha YFM 700 Grizzly
- 2010 Yamaha YFM 550 Grizzly
- 2009 Yamaha YFM 700 Grizzly
- 2009 Yamaha YFM 550 Grizzly
- 2008 Yamaha YFM 700 Grizzly
- 2007 Yamaha YFM 700 Grizzly
Dimensions Stator
Interior diameter : 45 mm
Exterior diameter : 106 mm
Thickness : 27 mm
Length of wires stator to grommet : 100 mm
Length of wires grommet to plug : 550 mm & 1100 mm
Length of pickup coil's wire to grommet : 80 mm
Other specifications :
Number of wires : 5
Number of plugs : 2
Number of pins : 5
Wire to wire resistance :
Alternator : Between each White = 0.4 ohms +/-20%
Alternator : White to Ground = 0.L on Display
Pickup : White to Grey = 500 ohms +/-20%
Dimensions Mosfet Voltage Regulator
Width : 95 mm
Length : 30 mm
Height: 110 mm
Fixation holes center to center :78 mm
Other specifications :
Number of plugs : 2
Number of pins : 5
Minimum Charging Voltage: 14.5 V +/- 0.5 V
Maximum Charging Current: 50 A / 500 W
Open Circuit Voltage: < 15 V
Operation Temperature: -20° to 85°
- Check the AC output of the stator
- Replace any burned or corroded connectors on stator and regulator/rectifier
- Check and repair any melted wiring
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original.
All the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010".
- Check the AC output of the stator
- Replace any burned or corroded connectors on stator and regulator/rectifier
- Check and repair any melted wiring
- Use hi-temp dielectric grease on all connectors
Brand new aftermarket Stator + Crankcase cover Gasket + Mosfet Voltage Regulator Kit
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation
- All shipped products are tested
All item pictures are accurate; if in doubt, do not hesitate to compare our item to your original part.
Stator- Highest grade of of lamination materials
- Highest grade of of copper winding, resistant to 200 degrees Celsius
- Stator crankcase cover gasket included
- Pick up pulsar coil included
- Connector included
- Rubber grommet included
Mosfet Voltage Regulator
STOP BURNING YOUR REGULATOR RECTIFIER !
It is time to update or replace your voltage regulator with the advanced MOSFET type.
It runs cooler than all OEM diode style regulators. In addition, this rectifier has overheat protection, rather than burn up it will simply turn off for a while and cool off.
- The quality exceeds the OEM equipment
- Improved heat sink and charging capabilities
- Higher grade of electric components
We have even included the opposite connector (main harness side) as we know these are often melted / corroded / defective and a major cause of repetitive electrical issues.
Battery condition is extremely important. No stator or voltage regulator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
Why use Mosfet Enhanced technology?
Runs cooler
Runs much cooler than the traditional Shunt voltage regulator rectifier.
Saves gas
Less load on the stator, less work, less fuel is used and you save.
Regulated energy
The power charging your battery is steadier and smooth.
Extended battery life
Extends the battery’s life and cold cranking capacity.
More engine power
Removes stator load resulting in more engine power.
Optimized power
Optimize power delivery by switching the stator coils on or off.