Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

Share This Product:

Vehicle Fitment

2015 Arctic Cat Prowler 700
2014 Arctic Cat Prowler 550
2014 Arctic Cat Prowler 1000
2014 Arctic Cat 1000 XT
2013 Arctic Cat TRV 550
2013 Arctic Cat Prowler 550
2013 Arctic Cat Prowler 1000
2013 Arctic Cat 550 EFI F/C
2013 Arctic Cat 1000 XT
2012 Arctic Cat TRV 700
2012 Arctic Cat TRV 550
2012 Arctic Cat TRV 1000
2012 Arctic Cat TBX 700
2012 Arctic Cat Prowler 700
2012 Arctic Cat Prowler 550
2012 Arctic Cat Prowler 1000
2012 Arctic Cat Mudpro 700
2012 Arctic Cat Mudpro 1000
2012 Arctic Cat 700
2012 Arctic Cat 550 EFI F/C
2012 Arctic Cat 1000
2011 Arctic Cat TRV 700
2011 Arctic Cat TRV 550
2011 Arctic Cat TRV 1000
2011 Arctic Cat TBX 700
2011 Arctic Cat Prowler 700
2011 Arctic Cat Prowler 550
2011 Arctic Cat Prowler 1000
2011 Arctic Cat Mudpro 700
2011 Arctic Cat Mudpro 1000
2011 Arctic Cat 700 H1
2011 Arctic Cat 550 EFI F/C
2011 Arctic Cat 1000
2010 Arctic Cat Thundercat 1000
2010 Arctic Cat TRV 700
2010 Arctic Cat TRV 550
2010 Arctic Cat TRV 1000
2010 Arctic Cat TBX 700
2010 Arctic Cat Prowler 700
2010 Arctic Cat Prowler 550
2010 Arctic Cat Prowler 1000
2010 Arctic Cat Mudpro 700
2010 Arctic Cat Mudpro 1000
2010 Arctic Cat 700 H1
2010 Arctic Cat 550 H1 EFI F/C
2010 Arctic Cat 550 EFI F/C
2009 Arctic Cat Thundercat 1000
2009 Arctic Cat TRV 700
2009 Arctic Cat TRV 1000
2009 Arctic Cat Prowler 700
2009 Arctic Cat Prowler 550
2009 Arctic Cat Prowler 1000
2009 Arctic Cat Mudpro 700
2009 Arctic Cat 700 H1
2008 Arctic Cat Thundercat 1000
2008 Arctic Cat Prowler 700
2008 Arctic Cat 700 H1

Interchange Part No

0802-041

Specifications

Dimensions :
Interior diameter : 53 mm
Exterior diameter : 114 mm
Thickness : 17 mm
Length of wires stator to grommet : 100 mm
Length of wires grommet to plug : 300 mm
Length of pickup coil's wire to grommet : 70 mm

Other specifications :
Number of wires : 5
Number of plugs : 2
Number of pins : 5

Wire to wire resistance :
Alternator : White Between Each White = 0.4 ohms +/-20%
Pickup : Blue To Green = 200 ohms +/-20%

Installation

Before installing your new stator

Check the AC output of the stator.
Replace any burned or corroded connectors on stator and regulator/rectifier
Check and repair any melted wiring.
Use hi-temp dielectric grease on all connectors

Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010’’.

Details