Mosfet Regulator for Victory Vegas 8 Ball / Hammer / Kingpin / High-Ball / Judge / Boardwalk / Gunner 1800 2008-2017
Battery condition is important. No regulator can make up for a bad or weak battery. If in doubt charge your battery and have it load tested, or simply replace it. ALWAYS START WITH A FULLY CHARGED BATTERY !
- 2017 Victory Vegas
- 2017 Victory Judge
- 2017 Victory High-Ball
- 2017 Victory Hammer
- 2017 Victory Gunner
- 2016 Victory Vegas 8 Ball
- 2016 Victory Vegas
- 2016 Victory Judge
- 2016 Victory Jackpot
- 2016 Victory High-Ball
- 2016 Victory Hammer
- 2016 Victory Gunner
- 2015 Victory Vegas 8 Ball
- 2015 Victory Judge
- 2015 Victory Jackpot
- 2015 Victory High-Ball
- 2015 Victory Hammer
- 2015 Victory Gunner
- 2015 Victory Boardwalk
- 2014 Victory Vegas 8 Ball
- 2014 Victory Judge
- 2014 Victory Jackpot
- 2014 Victory High-Ball
- 2014 Victory Hammer
- 2014 Victory Boardwalk
- 2013 Victory Vegas 8 Ball
- 2013 Victory Judge
- 2013 Victory Jackpot
- 2013 Victory High-Ball
- 2013 Victory Hammer
- 2013 Victory Boardwalk
- 2012 Victory Vegas 8 Ball
- 2012 Victory Vegas
- 2012 Victory Kingpin
- 2012 Victory Jackpot
- 2012 Victory High-Ball
- 2012 Victory Hammer
- 2011 Victory Vegas 8 Ball
- 2011 Victory Vegas
- 2011 Victory Kingpin
- 2011 Victory Jackpot
- 2011 Victory Hammer
- 2010 Victory Vegas 8 Ball
- 2010 Victory Kingpin
- 2010 Victory Jackpot
- 2010 Victory Hammer
- 2009 Victory Vegas 8 Ball
- 2009 Victory Kingpin
- 2009 Victory Jackpot
- 2009 Victory Hammer
- 2008 Victory Vegas 8 Ball
- 2008 Victory Kingpin
- 2008 Victory Jackpot
- 2008 Victory Hammer
4012240
4012241
4011559
4011961
4011962
4013395
Dimensions:
Width: 108 mm
Length: 112 mm
Height: 51 mm
Stator Wire length : 130 mm
Battery Wire length : 200 mm
Distance between fixation holes center to center: 82 mm
Other specifications:
Number of plugs: 2
Number of pins: 5
Number of wires: 5
Minimum Charging Voltage: 14.5 V +- 0.5 V
Maximum Charging Current: 50 A / 500 W
Open Circuit Voltage: < 15 V
Operation Temperature: -20°C to 85°C
Before installing your new Mosfet Voltage Regulator Rectifier :
- Check the AC output of the stator
- Replace any burned or corroded connectors on stator and regulator rectifier
- Check and repair any melted wiring
- Use hi-temp dielectric grease on all connectors
Why use Mosfet Enhanced technology?
Runs cooler
Runs much cooler than the traditional Shunt voltage regulator rectifier.
Saves gas
Less load on the stator, less work, less fuel is used and you save.
Regulated energy
The power charging your battery is steadier and smooth.
Extended battery life
Extends the battery’s life and cold cranking capacity.
More engine power
Removes stator load resulting in more engine power.
Optimized power
Optimize power delivery by switching the stator coils on or off.
With design
This product is an advanced design that lowers operating temperatures for extended longevity and better performance than the OEM part.Brand new Mosfet Voltage Regulator Rectifier
STOP BURNING YOUR REGULATOR RECTIFIER !It is time to update or replace your voltage regulator with the advanced MOSFET type.
It runs cooler than all OEM diode style regulators. In addition, this rectifier has overheat protection, rather than burn up it will simply turn off for a while and cool off.
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation
- The quality exceeds the OEM equipment
- Higher grade of electric components
- All shipped products are tested
All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part.