Stator for Triumph Speed Triple 1050 | Speed Triple 1050 R | Sprint GT 1050 | Sprint ST 1050 | Tiger 1050 | 1994-2020

$USD 139.00
Availability: In stock
SKU
RM01390
Please note: that some Triumph models have multiple stator for some models. Please refer to the note below to make sure you have the right part. Speed triple R from 2011 to 2017 : This part will only fit on Speed triple R with a vin lower than 735336. For models with an higher vin than 735337, refer to OEM# T1300118. Sprint ST 2019 to 2020 This part fits vehicles with vin 208167 and up. For vehicles with vin up to 139276, refer to OEM# T1300350 and for vehicles with vin from 139277 to 208166, refer to OEM# T1300502. Speed Triple 1994 to 2018 This part will only fit Speed Triple with a vin between 210445 and 461331 and an engine number higher than 356143 or a vin between 461332 and 735437. If your vehicle has a vin between 141872 and 210444 and has a engine number higher than 183487 or a vin between 210445 and 461331 and an engine number lower than 356142, refer to OEM# T1300610. If your vehicle has a vin between 141872 and 210444 and with an engine number lower than 183486, refer to OEM# T1304040. If your vehicle has a vin lower than 141871, refer to OEM# T1300350. Speed Triple 1050 2005-2010 : compare the dimension of your original product with the dimension of our product before buying. The dimensions for this stator are : Exterior diameter : 115 mm, Interior diameter : 42 mm, Thickness : 22 mm. This stator will fit engine serial number 356143 and up. Aftermarket replacement part for: Triumph Speed Triple 1050 -- 1994-2018. Triumph Speed Triple 1050 R -- 2011-2017
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
T1300111
T1300509

Dimensions :
Interior diameter : 42 mm
Exterior diameter : 115 mm
Width : 22 mm

Other specifications :
Number of wires : 3
Number of plugs : 1
Number of terminals : 3
Harness length Stator to grommet : 110 mm
Harness length grommet to plug : 600 mm

Wire to wire resistance :
Alternator : Black between each Black = 0.5 ohms +/- 20%

Before installing your new stator
  • Check the AC output of the stator.
  • Replace any burned or corroded connectors on stator and regulator/rectifier
  • Check and repair any melted wiring.
  • Use hi-temp dielectric grease on all connectors

Our stator may use a different wire color code than your original. `
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010’’.

Brand new generator stator

  • Direct replacement to your original unit
  • Plug-and-play, direct fit, easy installation.
  • Highest grade lamination materials
  • Highest grade copper windings, resistant to 200 degrees Celsius.
  • Connector included
  • Rubber grommet included
  • All products shipped are tested

We have even included the opposite connector (main harness side) as we know these are often melted/corroded/defective and a major cause for repetitive electrical issues.

All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.

Write Your Own Review
You're reviewing:Stator for Triumph Speed Triple 1050 | Speed Triple 1050 R | Sprint GT 1050 | Sprint ST 1050 | Tiger 1050 | 1994-2020
Your Rating
Customers Also Viewed
Currently there is no product to display.