Stator for Arctic Cat CRF Crossfire 700 | F6 / F7 Firecat | M6 600 | Mountain Cat 600 2005-2006 | 3007-018 / 3006-943
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
- 2006 Arctic Cat Sabercat 700 EFI L/C
- 2006 Arctic Cat Sabercat 600 LX EFI L/C
- 2006 Arctic Cat Mountain Cat 600 EFI L/C
- 2006 Arctic Cat M7 700 EFI L/C
- 2006 Arctic Cat M6 600 EFI L/C
- 2006 Arctic Cat F7 Firecat 700 Sno Pro EFI L/C
- 2006 Arctic Cat F7 Firecat 700 R EFI L/C
- 2006 Arctic Cat F7 Firecat 700 EFI L/C
- 2006 Arctic Cat F6 Firecat 600 R EFI L/C
- 2006 Arctic Cat F6 Firecat 600 EFI L/C
- 2006 Arctic Cat CF CrossFire 700 Sno Pro EFI L/C
- 2006 Arctic Cat CF CrossFire 700 EFI L/C
- 2006 Arctic Cat CF CrossFire 600 EFI L/C
- 2005 Arctic Cat Sabercat 700 LX EFI L/C
- 2005 Arctic Cat Sabercat 700 EFI L/C
- 2005 Arctic Cat Sabercat 600 LX EFI L/C
- 2005 Arctic Cat Sabercat 600 EFI L/C
- 2005 Arctic Cat Mountain Cat 600 EFI L/C
- 2005 Arctic Cat M7 700 EFI L/C
- 2005 Arctic Cat M6 600 EFI L/C
- 2005 Arctic Cat F7 Firecat 700 Sno Pro EFI L/C
- 2005 Arctic Cat F7 Firecat 700 EFI L/C
- 2005 Arctic Cat F6 Firecat 600 EFI L/C
3006-943
Dimensions :
Interior diameter : 47 mm
Exterior diameter : 115 mm
Thickness : 20 mm
Length of wires stator to plug : 500 mm
Other specifications :
Number of wires : 9
Number of plugs : 1
Number of pins : 9
Wire to wire resistance :
Alternator 1 : Yellow between each Yellow = 0.4 ohms +-20%
Alternator 2 : White/Blue between each White/Blue = 17.2 ohms +-20%
Pickup : Orange between each Orange= 2 ohms +-20%
Source 1 : Green to Brown = 10 ohms +-20%
Source 2 : Green to Black = 10 ohms +-20%
- Check the AC output of the stator.
- Replace any burned or corroded connectors on stator and regulator/rectifier
- Check and repair any melted wiring.
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010".
Please note: Your model may not need the brown wire. Please remove it if this is the case for your machine
Brand new stator
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation.
- Highest grade lamination materials
- Highest grade copper windings, resistant to 200 degrees Celsius.
- Connector included
- All products shipped are tested
All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.
Please note: Your model may not need the brown wire. Please remove it if this is the case for your machine