Stator 200W + Regulator + PeakRPM CDI Box + Ext. Ignition Coil + Flywheel + Puller for Yamaha YFZ 350 Banshee 1987-1994

$USD 466.00
Availability: In stock
SKU
RM23008
RM23008
High output stator
Number of wires : 6
Number of terminals : 6
Alternator : Yellow to Black = 0.4 ohms+/-20%
Pick up 1 : White/Green to White/Red = 115 ohms+/-20%
Source 1 : Green to Red = 12 ohms+/-20%

High performance CDI box
The only real way to test your CDI box is to swap it out with another known good unit from the same year/make/model. Because of this, we recommend that you rule everything else out before replacing the CDI box.


External ignition coil
Bracket center to Bracket: 90mm


Improved flywheel
Diameter of fly wheel- 130mm


Flywheel puller
27 MM x 1.0 Left hand male
Before installing your new stator

  • Check the AC output of the stator.
  • Replace any burned or corroded connectors on stator and regulator/rectifier
  • Check and repair any melted wiring.
  • Use hi-temp dielectric grease on all connectors

Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.

When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010".

CDI Box HP

Our CDI may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This CDI is designed as a direct plug-in replacement and should be used as such.

Improved Flywheel

Before attempting to start your banshee adjusting the air gap is necessary.

Rotate the flywheel so the raised node is lined up with the pick up/pulser coil and adjust as close as possible but no less than 0.010".

External ignition coil

Remove the yellow wire from the external ignition coil, if it is not applicable to your model.

Brand new high output Stator + Voltage Regulator Rectifier + PeakRPM CDI Box + Flywheel puller + Flywheel + External ignition coil Kit

  • Direct replacement to your original unit
  • Plug-and-play, direct fit, easy installation
  • The Quality exceeds the OEM equipment
  • All shipped products are tested

*All item pictures are accurate; if in doubt, do not hesitate to compare our item to your original part.

High output stator 200 watts
  • Highest grade of lamination materials
  • Highest grade of copper winding, resistant to 200 degrees Celsius
  • Pick up pulsar coil included
  • Connector included
  • Rubber grommet included
  • Adjustable timing plate to advance and retard up to 10 degrees included
AC Regulator
  • 12 Volts regulator used by Baja winners
  • For use with all standard halogen and quartz lights
  • Precise voltage control, eliminates light burnout
  • Reduce flickering and dimming
  • Works with all other OEM parts
  • Rated at 225 watts
PeakRPM CDI box
  • Our PeakRPM CDI Box provides the optimal output for your ride
  • Higher grade of electronic components
Improved stronger magneto flywheel rotor

RMSTATOR is offering a new replacement flywheel with stronger magnets for your YAMAHA YFZ350 BANSHEE, this flywheel can be used as a direct replacement to the OEM.

Flywheel puller
  • 27 MM x 1.0 Left hand male
External ignition coil Please note : For solid tip spark plugs, you may re-use your original spark plug caps.
  • Highest grade of lamination materials
  • Spark plug cap(s) included
Write Your Own Review
You're reviewing:Stator 200W + Regulator + PeakRPM CDI Box + Ext. Ignition Coil + Flywheel + Puller for Yamaha YFZ 350 Banshee 1987-1994
Your Rating
Customers Also Viewed
Currently there is no product to display.