Generator Stator for Husaberg 390 450 570 FE / FX | Husquvarna TE 250 300 | KTM 500 505 525 ECX / XC-W / SX-F 2008-2020
Battery condition is extremely important. No stator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.
- 2020 KTM 300 XC-W
- 2020 KTM 300 XC
- 2020 KTM 300 EXC Euro
- 2020 KTM 250 XC-W
- 2020 KTM 250 XC
- 2020 KTM 250 EXC Euro
- 2019 KTM 300 XC-W
- 2019 KTM 300 EXC Euro
- 2019 KTM 250 XC-W
- 2019 KTM 250 EXC Euro
- 2019 Husqvarna TE 300i
- 2019 Husqvarna TE 250i
- 2018 KTM 300 EXC Euro
- 2018 KTM 250 XC-W
- 2018 KTM 250 EXC Euro
- 2018 Husqvarna TE 300
- 2018 Husqvarna TE 250i
- 2017 KTM 450 Rally Factory Replica
- 2016 KTM 500 XC-W
- 2016 KTM 500 EXC
- 2016 KTM 450 XC-W
- 2016 Husaberg FE450
- 2015 KTM 500 XC-W
- 2015 KTM 500 EXC
- 2015 KTM 450 XC-W
- 2015 Husaberg FE450
- 2014 KTM 500 XC-W
- 2014 KTM 500 EXC
- 2014 KTM 450 XC-W
- 2014 Husaberg FE450
- 2013 KTM 500 XC-W
- 2013 KTM 500 EXC
- 2013 KTM 450 XC-W
- 2013 Husaberg FE450
- 2013 Husaberg FE 501
- 2012 KTM 525 XC
- 2012 KTM 505 SX
- 2012 KTM 500 XC-W
- 2012 KTM 500 EXC
- 2012 KTM 450 XC-W
- 2012 Husaberg FE570
- 2012 Husaberg FE450
- 2012 Husaberg FE390
- 2011 KTM 525 XC
- 2011 Husaberg FX450
- 2011 Husaberg FE570
- 2011 Husaberg FE450
- 2011 Husaberg FE390
- 2010 KTM 525 XC
- 2010 KTM 505 SX
- 2010 KTM 450 XC-F
- 2010 KTM 450 SX-F
- 2010 Husaberg FX450
- 2010 Husaberg FE570
- 2010 Husaberg FE450
- 2010 Husaberg FE390
- 2009 KTM 525 XC
- 2009 KTM 505 SX
- 2009 KTM 450 XC-F
- 2009 KTM 450 SX-F
- 2009 Husaberg FE570
- 2009 Husaberg FE450
- 2008 KTM 525 XC
- 2008 KTM 450 XC-F
55439104100
83039004000
Dimensions :
Interior diameter : 35 mm
Exterior diameter : 89 mm
Thickness : 18 mm
Length of wires stator to grommet : 94 mm
Length of wires grommet to plug : 406 mm
Other specifications :
Number of wires : 3
Number of plugs : 1
Number of pins : 3
Wire to wire resistance :
Alternator : Black between Black = 0.4 ohms +-20%
Before installing your new stator
- Check the AC output of the stator
- Replace any burned or corroded connectors on stator and regulatorrectifier
- Check and repair any melted wiring
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010".
Brand new aftermarket generator stator
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation
- Highest grade lamination materials
- Highest grade copper windings, resistant to 200 degrees Celsius.
- Connector included
- Rubber grommet included
- All products shipped are tested
All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.