High Output Stator 200 W + Voltage Regulator Rectifier + High Performance CDI Box for Yamaha YFZ 350 Banshee 1987-1994

CAD$ 433.00
Availability: In stock
SKU
RM23009
RM23009

High output stator 200 watts Dimensions
Interior diameter: 41 mm
Exterior diameter: 103 mm
Thickness: 14 mm
Length of wires stator to grommet: 90 mm
Length of wires grommet to plug: 380 mm
Length of pickup coil's wire to grommet: 100 mm

Other specifications:
Number of wires: 6
Number of plugs: 3
Number of pins: 6

Wire to wire resistance:
Alternator: Black to Yellow = 0.2 ohms +/-20%
Pickup: White/Red to White/Green = 100 ohms +/-20%
Source: Red to Green = 15 ohms +/-20%

AC Regulator Dimensions
Width: 45 mm
Length: 45 mm
Height: 20 mm
Wires length: 130 mm

Other specifications:
Number of wires: 2
Number of terminals: 2
Minimum Charging Voltage: 13 V +/- 0.5 V
Maximum Charging Current: 6 A - 10 A / 50 W - 200 W
Open Circuit Voltage: 15 V
Operation Temperature: -20⁰ to 85⁰

Please note: This regulator has two wires, yellow to power and black to ground.

High performance CDI Box Dimensions
Height: 25 mm
Length: 85 mm
Width: 71 mm
Wires length : 120 mm & 140 mm
Fixation holes center to center: 85 mm

Other specifications:
Number of plugs: 8
Number of pins: 2

Please note: The only real way to test your CDI box is to swap it out with another known good unit from the same year/make/model. Because of this, we recommend that you rule everything else out before replacing the CDI box.

Before installing your new stator

  • Check the AC output of the stator.
  • Replace any burned or corroded connectors on stator and regulator/rectifier
  • Check and repair any melted wiring.
  • Use hi-temp dielectric grease on all connectors

Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010’’.

Before installing your new regulator/rectifier:

  • Bolt regulator to frame
  • Ground Black wire to Frame or Harness Ground
  • Connect Yellow Wire to AC Output lead of the Stator

CDI Box HP

Our CDI may use a different wire color code then your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This CDI is designed as a direct plug-in replacement and should be used as such. .

Brand new high output stator 200 watts, AC voltage regulator rectifier and high performance CDI box

  • Direct replacement to your original unit
  • Plug-and-play, direct fit, easy installation.
  • The Quality exceeds the OEM equipment
  • All product shipped are tested
  • All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.

High output stator 200 watts

  • Highest grade lamination materials
  • Highest grade copper winding, resistant to 200 degrees Celsius.
  • Pick up pulsar coil included
  • Connector included
  • Rubber grommet included
  • Adjustable timing plate to advance and retard up to 10 degrees included

AC Regulator

  • 12 Volts regulator used by Baja winners
  • For use with all standard halogen and quartz lights
  • Precise voltage control, eliminates light burnout
  • Reduce flickering and dimming
  • Rated at 225 watts.

High performance CDI Box

  • Enhanced timing curve, increased rev limiter
  • Higher grade of electronic components.
Write Your Own Review
You're reviewing:High Output Stator 200 W + Voltage Regulator Rectifier + High Performance CDI Box for Yamaha YFZ 350 Banshee 1987-1994
Your Rating
Customers Also Viewed
Currently there is no product to display.